Drew Technologies DashDAQ Series II Manual de instrucciones

DashDAQ Series II Instruction Manual 2 Dear Customer, Congratulations! You have just purchased the most powerful,

19 2.4 Menu Map 20 2.5 New Vehicle Setup The DashDAQ was designed to be used on any OBDII vehicle. OBDII vehicles have many “signals” or

21 3 Gauge Setup & Navigation This section describes how to setup gauges and navigate. 3.1 Navigating Gauges: To access DashDAQ gauges, t

23 3.3 Set Gauge Min/Max Values The DashDAQ allows users to specify the data range for each gauge. Tap on the [Minimum] button to set the b

25 The DashDAQ allows users to assign different colors to the signals assigned to a particular gauge. The signal will be displayed in

27 the signals displayed on the gauges. 3. When finished with your log session tap [End Log]. Your results are now saved to the memory card.

29 4 DashDAQ Setup Menu This section describes the setup menu. 4.1 Installed Devices The Installed Devices section of the setup menu is what makes

31 6. To select the Innovate LC-1, use the [<] or [>] buttons to navigate to the “Wideband” selection. 7. Tap [Innovate LC-1] to high

33 4.2 Clock The clock setup option allows the user to set the on board clock to current time and date. This information will be time-stamp

35 4.4 Backup To SD Card Backup to SD is the setup option that allows you to backup various user specific setting of the DashDAQ. One example

37 4.7 Dashboard Theme The DashDAQ has a very powerful graphical interface that allows its users to change the look and feel of the

3 Table Of Contents 1 Installation... 9 1.1 SAFETY FIRST! ... 9

39 4.9 Logfile Prefix The Logfile Prefix is the name that is attached to the beginning of a log file. When you tap “Start Log” from a gau

41 6. Tap [Yes] if you would like to clear the codes and turn your check engine light off. Note: This does not solve any underlying v

43 4. Bring your vehicle to a stop and tap [Start]. When the drag-strip “tree” turns green, accelerate. 5. The measurement will autom

45 4. Tap [Change]. This screen appears: 5. Tap [Driver]. 6. To select the Dyno Calculator, use the [<] or [>] buttons to navigate

47 3. You will need to tap on each signal and tap [Change] to specify the values of each. The DashDAQ is row ready to calculate horsep

49 5. Tap [Driver]. 6. To select the Fuel Economy Calculator, use the [<] or [>] buttons to navigate to the “Calculator” sele

51 5. Tap on the desired measurement and tap [Save]. Tap [Save] again to view the calculation on the gauge. 9 Parameters From the Ma

53 3. Windows will do a preliminary search for the driver, but will not find one. This screen will appear: 54 4. Click on [Browse

55 11.2 Update your DashDAQ: 1. Connect the USB cable to the single USB port on the left as you look at the DashDAQ screen, and then to y

57 12 APPENDIX 12.1 Support Please be sure to reference our online FAQ’s. All support questions can be answered at the online forums

5 Components Included with DashDAQ • Display Unit • Windshield Mount and four Screws • USB Cable • OBDII Cable • Software CD

59 12.3 Limited Warranty Drew Technologies, Inc. guarantees that every DashDAQ Series II is free from physical defects in material and

61

7 IMPORTANT! THIS IS A HIGH PERFORMANCE PRODUCT, USE AT YOUR OWN RISK Do not use this product until you have carefully read the follow

9 1 Installation 1.1 SAFETY FIRST! The installation of the DashDAQ must be done in such a manner that it does not interfere with t

11 Cable routing tips: • Find your OBDII connector first and work the cable to where it is to be mounted on the windshield. • Route your

13 Connections (cont.) USB Ports Power Button MMC SD Memory Card Slot 14 1.8 SD Memory Card Always insert and remove the memory card

15 2 Basic Operation This section describes the basic operation of the DashDAQ. 2.1 Low Power Mode The DashDAQ has a low power mode built in

17 Tapping the tap the [I Accept] button will cause the gauge screen to appear: The [<<] and [>>] arrow buttons at the bottom allow yo